Corrugated Sample Maker CNC 2026 CE EVA Carton Cutter

Configured Cutting Method — Knife and laser cutting technologies developed in-house, so the cutting process matches the material rather than forcing a single method across incompatible substrates.

Technical Specifications

Application Suitability

Why Voltage Confirmation Must Happen Before the Quotation

A machine that cannot power on at your facility is not a machine — it is a crate of steel sitting on your dock for weeks.

Last year a packaging sample maker ordered a CO2 laser cutting and engraving machine manufacturer system for corrugated prototyping. The workshop ran 220V three-phase. The machine shipped at 380V. Nobody caught the mismatch until the electrician opened the cabinet. Three weeks of lost sample deadlines while a transformer was sourced locally. That delay had nothing to do with the cutting technology and everything to do with skipping a ten-minute voltage check [NEED_CITE: voltage and frequency standards by export market]. Most electrical incompatibilities on exported cutting equipment surface only after the crate is opened, by which point the buyer has already committed floor space and production schedules.

Swiss Knife Head with Full-Cut and Half-Cut Modes

The tool head on this flatbed uses a Swiss imported oscillating knife capable of full cutting through the substrate and half cutting for crease-line scoring. For corrugated carton sample making, the half-cut mode presses the creasing wheel into the flute structure without severing the board, producing fold lines that hold shape during manual assembly. Switching between modes is handled through the software nesting file, so a single job can contain cut contours and crease paths without manual tool changes mid-sheet.

Honeycomb Vacuum Hold-Down Across the Full Bed

A 7.5 kW vacuum pump pulls air through the aluminum alloy honeycomb table surface to pin the workpiece flat. Corrugated board tends to curl at the edges after storage, and even slight lift causes the knife to skip or tear the flute. The honeycomb structure distributes suction uniformly, so a 1600×2500 mm sheet stays seated without mechanical clamps blocking the cutting path. Small sticker parts can ride on the same surface provided the vacuum zoning is matched to the part footprint [NEED_CITE: vacuum table zoning principles for CNC cutting].

Reading the Specs That Matter for Packaging Work

The 1600×2500 mm working area accommodates standard corrugated sheets used in packaging sample development, allowing multiple carton blanks to be nested in one cycle. Repeatability of ≤0.1 mm means that crease lines land within tolerance for folding jigs and automated erecting machines downstream. Taiwan Delta servo motors paired with Hiwin linear rails keep the carriage stable at translational velocities up to 1200 mm/s, which matters when long straight cuts dominate the job. The HP-GL compatible instruction system accepts files from most packaging CAD suites, reducing the conversion step between design and machine. The professional carton nesting software is included and supports multi-format import so existing DXF or PLT workflows carry over without new licensing costs.

What Happens When Tooling Is Chosen by Guesswork

Selecting a drag knife for corrugated board that actually requires an oscillating knife produces crushed flutes and ragged edges, forcing the operator to slow the feed rate or scrap the sample. On flexible materials like sponge composite leather, insufficient vacuum zoning lets the sheet shift during high-speed contour cuts, shifting the cut line away from the printed register mark. These are not catastrophic failures — the machine still runs — but the output fails quality checks and the operator loses time re-nesting the job [NEED_CITE: common tooling mismatch consequences in CNC flatbed cutting].

Why Buyers Come Back for a Second Machine

Both knife and laser cutting technologies are engineered in-house, so when a packaging maker needs to add acrylic template cutting later, the conversation starts with material properties rather than pushing one machine type to do everything. Every tool head and table configuration is specified against the buyer’s declared material and thickness before the order is locked. CCD camera positioning can be added for printed contour work on labels and stickers, and the tracking capability is demonstrated on the buyer’s own printed sheet before commitment. Software file-format compatibility is confirmed in writing so existing nesting workflows transfer without rework. Voltage, plug type, and control-language customization are finalized at the electrical-drawing stage — which is exactly where the lesson from that three-week transformer delay gets applied.

Documentation & Verification

• Electrical schematic with confirmed voltage and plug type for your facility
• Sample cutting report produced on your own corrugated or sticker stock
• Tool head and vacuum table configuration list matched to declared material
• Software licence with confirmed file format compatibility note
• Factory test record covering repeatability and full-bed vacuum measurement
• Operation and maintenance manual in your selected control language

Installation, Commissioning & Support

• Dedicated 380V±10% circuit rated for the 9 kW total draw including the 7.5 kW vacuum pump
• Level concrete floor required for the 3450×2300×1250 mm footprint to maintain rail alignment
• Machine ships in bolted assembly sections; on-site reassembly and squareness check included
• First-run parameter setting for your specific board thickness and flute profile
• Operator training on nesting software import, tool head changeover, and vacuum zoning adjustment
• Spare oscillating knife blades, felt replacement panels, and conveyor belt sections stocked

Before You Request a Quote

Send the material type, sheet dimensions, and thickness range you cut most often so the tool head and vacuum zoning can be matched before pricing. Confirm your workshop voltage and phase supply at the breaker panel — not the building main — and note the plug standard your electrician prefers. If you run an existing nesting workflow, share a sample file so import compatibility is verified before the order is written.

Frequently Asked Questions

Q: How is the 200–800 mm/s cutting speed determined for my material?
A: Cutting speed depends on substrate density, flute profile, and knife oscillation frequency. Corrugated B-flute typically allows faster feed than double-wall. We run a sample cut on your actual board to record the speed that delivers a clean edge at full depth, and that figure is written into the sample report before you commit.

Q: Will the vacuum table hold small sticker parts without lifting?
A: The aluminum honeycomb surface provides full-bed suction, but very small parts benefit from zoned vacuum activation. We configure the table zones to match your typical part footprint and verify hold-down during the sample cutting stage so lift does not cause register drift at cutting speed.

Q: What file formats does the nesting software accept?
A: The included carton nesting software imports DXF, PLT, and HP-GL formats. We confirm compatibility with your specific CAD output by running a test import before the order is finalized, and the software licence is perpetual with language customization to match your operator preference.

Q: Is the voltage and control language locked in before shipment?
A: Yes. We produce an electrical schematic showing the exact voltage, phase, and plug type for your market and send it for your approval before the machine enters final assembly. Control panel language is set to your choice of English, Russian, Italian, Chinese, or a custom language specified at order.

Q: Can you cut samples on my own material before I place the order?
A: We require a sheet or roll of your actual production material shipped to the factory or sourced locally. The sample cutting report documents edge quality, crease depth, cycle time, and any tooling adjustments made, giving you a production-baseline reference before the purchase decision.