Honeycomb V-Slot Creasing Cutting Machine for Packaging – OEM Available

V-Slot Creasing on Honeycomb Board — the RT-D2516/RT-S2516 pairs a Swiss-imported oscillating knife with a dedicated creasing wheel, validated on the buyer’s own board grade before shipment rather than relying on generic cutting charts.

Technical Specifications

Application Suitability

What Happens When Corrugated Gets the Wrong Tool Head

Crushed cores and ragged edges start from a mismatch between tool head and board structure, not from the machine itself.

I have stood in packaging workshops where the board looked fine at the edge but the internal fluting was visibly compressed, producing a crease that would not fold cleanly on the packing line. The issue usually traced back to a drag knife forced through honeycomb or corrugated stock that needed a high-frequency oscillating blade instead. When a packaging CNC cutting machine manufacturer specifies the tool head after reviewing your actual board grade — not before — that problem disappears before the machine ships [NEED_CITE: corrugated and honeycomb board crushing thresholds under mechanical cutting].

Oscillating Knife and Creasing Wheel on One Head

The Swiss-imported oscillating knife on the RT-D2516/RT-S2516 handles full cutting, half cutting, and cursor location through a single tool head mount. This means a packaging CNC cutting machine operator can switch between cutting through corrugated stock and scoring a fold line without a manual tool change, reducing setup time between jobs. The creasing wheel is configured for V-slot profiles on honeycomb and corrugated board, which is where standard round-nose creasing tools tend to tear the liner rather than compress it.

Vacuum Table Stability for Thin and Lightweight Stock

The aluminum alloy honeycomb vacuum table provides a flat adsorption surface across the full 1600×2500 mm work area. Lightweight carton stock and small die-cut parts are the materials most likely to lift during high-speed cutting, so uniform vacuum distribution matters more than total suction power alone. The honeycomb structure also resists deflection under vacuum load, which maintains consistent material contact across the entire table [NEED_CITE: vacuum table zoning requirements for small-part holding in flatbed digital cutting].

Reading the Specs That Matter for Board Work

Cutting thickness is rated at ≤100 mm but varies with material — honeycomb board at that depth behaves very differently from solid corrugated, and the actual limit for your specific board grade should be confirmed with a sample cut. Repeated accuracy of ≤0.1 mm is delivered by the Taiwan Delta servo and Hiwin linear guide combination, which matters when crease lines must register precisely with printed graphics. Translational velocity of 800–2000 mm/s determines travel speed between cuts, while cutting speed depends on board density and thickness. The Taiwan Hiwin rail and rack transmission provide the rigidity needed to maintain that accuracy over the full 2500 mm travel length without mid-run drift. The 7.5 kW vacuum pump is sized to hold board stock across the full table area, though vacuum zone configuration should be confirmed for small-part jobs.

The Cost of Skipping Configuration Verification

Buyers who specify only working area and skip the tool head conversation often discover after delivery that their honeycomb board requires a creasing pressure or knife frequency the ordered configuration does not deliver. Voltage incompatibility is another late-stage problem — 380V ±10% is standard, but facilities running 220V/60Hz or other regional supply need confirmation before production begins. When CCD camera contour recognition is required for printed carton work, availability on this model must be verified since it is not explicitly confirmed in the current specification sheet [NEED_CITE: CCD camera positioning requirements for printed packaging contour cutting].

Why This Manufacturer for Packaging Board Work

In-house design covers both knife and laser cutting technologies, so the cutting method is matched to the board type rather than forced into one process. Tool head and table configuration are specified per material and production volume, not offered as a fixed package. Sample cutting on the buyer’s own honeycomb or corrugated board is standard before commitment, with edge quality and crease depth documented in a cutting report. Software compatibility with existing file formats is confirmed at the order stage, preventing the situation where a nesting workflow will not import on arrival. Voltage, control language, and plug type are locked in before shipment, matching the destination facility.

Documentation & Verification

• Machine specification sheet covering oscillating knife and creasing wheel tool head configuration
• Sample cutting report on buyer’s own honeycomb or corrugated board with measured edge and crease results
• Electrical schematic with 380V ±10% confirmation and destination voltage verification
• Software licence and file format compatibility note for carton design software
• Spare parts list including knife blades, creasing wheel inserts, and vacuum table seals
• Packing photographs documenting machine condition before container loading

Installation, Commissioning & Support

• Foundation must support 3450×2300×1250 mm machine footprint with level floor tolerance for the honeycomb vacuum table
• Dedicated 380V ±10% circuit rated for 9 kW total plus 7.5 kW vacuum pump startup surge
• Table leveling and vacuum zone calibration performed on-site after arrival at full working area
• First-run parameter setting includes cutting speed and creasing depth tuning on buyer’s board stock
• Operator training covers tool head changeover between oscillating knife, creasing wheel, and optional tools
• Spare knife blades and creasing wheel inserts stocked for consumable replacement cycles

What to Include in Your Inquiry

Provide your board type, flute profile or honeycomb cell size, sheet dimensions, and typical thickness range so the tool head can be matched before quotation. Confirm your facility voltage and frequency, and specify the control interface language required on delivery. If your workflow uses specific CAD file formats, list them so software compatibility is verified at the order stage rather than after installation.

Frequently Asked Questions

Q: How is cutting thickness verified for honeycomb and corrugated board?
A: Maximum cutting thickness is rated at ≤100 mm but varies with board type. Honeycomb and corrugated each have different crush thresholds under oscillating knife pressure. We run sample cuts on your actual board grade to confirm clean edge quality and crease depth before the machine enters production, and those results are documented in a cutting report sent for your approval.

Q: Is CCD camera contour recognition available for printed carton work?
A: CCD camera availability on this model requires confirmation at the inquiry stage. If your production involves cutting around printed registration marks at speed, specify this requirement when you submit your board samples so we can verify tracking capability and include it in the machine configuration list before order confirmation.

Q: What software file formats does the carton design software support?
A: The included professional carton cutting software supports multiple file format imports and is HP-GL compatible. Before you place the order, provide the specific file formats your design team uses so we can confirm import compatibility and test your sample files on the machine during factory acceptance.

Q: What voltage and language options are available for export?
A: Standard voltage is 380V ±10%. If your facility runs 220V/60Hz or another regional supply, specify this during inquiry so the electrical system is configured before production. Control interface language options include English, Russian, Italian, and Chinese, with special languages customizable to your operator requirements.

Q: Which spare parts should I stock for regular operation?
A: Oscillating knife blades, creasing wheel inserts, and vacuum table seals are the primary wear items. A spare parts list is included with the machine documentation, and we recommend confirming your stocking commitment at the order stage so consumables are available from the first day of production.